Home > Power Commander > Power Commander V Error

Power Commander V Error

Contents

Loading a Zero map in a Power Commander allows you to test the Power Commander basic functionality. Support the Site - Donations Accepted 100% for the members. 100% by the members. Copyright, Trademark and Disclaimer Notices | © 1995 - Dynojet Research, Inc. If the unit is not powered up, the computer will only see a USB device being plugged in, but will not allow the software to communicate. check over here

If the sensor tests out at a voltage near or at the lower limits of the specified range, the sensor should probably be replaced as it is an indication that it The Power Commander III USB needs power to complete this; either the 9-volt adapter or by running the engine. We did find that the zero and 100% throttle settings in the PCIII were WAY off, and this is something you have to set with the PC attached to the bike. Verify you are on the correct one.

Power Commander 3 Maps

There is two sets of connectors on this bike but one is grey and the other is black. From here on out, when you click Send/Get Map, both maps will be handled. Power Commander Installation Issues Answer Why doesn’t your AutoTune use 10/12mm o2 sensors?

Only the administrator will have access to your date of birth should you choose to hide it via the privacy option below. Verify the placement of the Throttle Position Sensor wire tap. A firmware update is not required unless you are having a problem, or want to take advantage of newer features. Power Commander 3 Software Answer Applicable to PC III USB The Power Commander 3 USB does not power up anymore after loading the firmware for my ignition module.

minkyhead is offline Quote Quick Reply post #7 of 16 Old 02-08-2010, 09:05 PM bwringer Stromthusiast! Power Commander 3 Usb This option is commonly used on with big motor builds, to get the bike to start when cold. You don't have to rev the bike out, the throttle just needs to go all the way to wide open and then back to idle. Next, select Edit for each gage in turn.

Today 02:18 PM by Oupoot 0 A look at the benefits... What Does A Power Commander Do For A Motorcycle Logged 2011Kawasaki KLX2502011 Yamaha XT1200Z R Competition White Explorer Edition spasm Hero Member Posts: 798 Re: The BIG Dynojet PowerCommander V and AutoTune Q&A topic « Reply #258 on: March 16, All you need to do is press "reset" while the bike running at idle, then quickly turn the throttle wide open till you hit the mechanical stop, then let go. It is a tight snap-in fit connection.

Power Commander 3 Usb

These maps were created with the model vehicle listed, with the modifications listed. http://www.yamahasupertenere.com/index.php?topic=2813.255 The software says "No Power Commander." Solutions: a.) Windows 98/ME - 1. Power Commander 3 Maps Dynojet creates target AFR tables for most of our pre-configured maps. Power Commander 3 Instructions This type of connection is prone to having this problem.

Also, relocation of the connector to under the right side cover, on top of the ECM, may be beneficial. check my blog Software Issues and Features Answer How do I lock a map on a PCIIIUSB? Today 04:51 PM by Chris92 3 Whould You Look At This?! Join Date: Oct 2009 Location: Indy Posts: 2,630 I'm also Mac or Ubuntu Linux only, but I found a pal with a PC laptop to come out to the garage and Power Commander 3 Installation

Answer Applicable to PC III USB I'm having trouble installing the Accelerator Pump Utility to my USB Power Commander III. Please try the request again. Many of today’s bikes (post 2007 or so) shut the injectors completely off during deceleration. http://exactcomputerrepair.com/power-commander/power-commander-3-usb-troubleshooting.html Vee2=2014+ DL1000s.

Any other locations may not supply a secure ground path and cause issues. Power Commander Tech Support If you are looking for the best fuel economy and not worried about making changed to the closed loop area you can leave the stock O2 sensors connected and still make I would suggest the 200, and for a stock bike probably not use the 300.

To setup the LCD unit, the vehicle has to be running.

Forgot your Password? Answer Applicable to PC III USB When I connect my PCIIIusb to my computer running Windows 98SE, it asks for “drivers”. Highlight the zero percent column and instead of using negative numbers, try adding fuel to the map. Power Commander V Tuning Tips It should have a constant green light on.

Please turn cookies on for bikeland.org. If you experience any problems with cruise control, or 6th gear indicator light on a newer Harley Davidson Touring bike with a Power Commander V installed. Dynojet has tested a few of the 10/12mm to 18mm adapters and found them to not work correctly. http://exactcomputerrepair.com/power-commander/power-commander-error-42.html Software Issues and Features Answer Do I need to use Get/Send Map or Table on the PCV?

This does not bode well for the Powercommander...or at least the map it came with. To load a map in a Power Commander, you need to have installed the correct Power Commander Software and maps. The Power Commander V only needs the USB cable to do this. Answer Applicable to PC III USB The Power Commander software says "Serial: N/A" at the top right hand corner of the screen and does not show any serial numbers or "TP"

Sure would have been nice if the instructions were to mention that. Make sure that the ignition module is communicating with the bike by showing a green indicator light on the front of the module once the bike is started. North American V-Stroms don't have O2 sensors. Make sure you are using the correct version of firmware for your device.

Dynojet is very conservative in giving out maps to customers everywhere in the world. Posts: 586 Pciii Uhb Yes, make sure the cord is locked fully into each port. Short term solution 2: Bypass the Flash installer and run the PC3 setup file manually. There is another set further down the harness that the connectors will fit into.

Installed everything and now my 2008 700 raptor wont even start but if i take to pcv out its starts and runs fine. Scooters&Mopeds!! Password: Confirm Password: Email Address Please enter a valid email address for yourself. Non-members please click here to register.

Power Commander V Check Engine Light and Error Codes P Thread Tools Search this Thread #1 03-16-2016, 01:29 PM drewsmith New Member Thread Starter Join The dual-channel AutoTune kit tunes more accurately (cylinder advanced), but is more expensive.