Home > Power Commander > Power Commander Usb Error Sending File

Power Commander Usb Error Sending File

Contents

Second thing is it was pre-program for a CBR929 and mine is a CBR954. If yours is not reading “zero” at idle with the motor at normal temperature, then use the following procedure to correct it. Verify where the connectors are hooked up. Make sure its connected to a new battery when you do it. check over here

Each .zip file contains the same map in 2 file formats - the older .map format is from the original PC3's which had a serial port, the newer .djm format is This feature was added to allow people using an LCD-200 to make easy adjustments to fuel, without a computer. During a firmware update my powercommander crapped out and went totally dead. Shown below are two graphs of a motorcycle before and after installation of the Power Commander.

Power Commander 3 Maps

Be sure you select the correct firmware for your device. The red curve shows a typical stock motorcycle with minor performance modifications (slip-on exhaust). Select a map you want to use, then Send Map to overwrite the current map with the one you have selected. In the Power Commander software, there is a utility to accomplish this.

It’s a judgment call which is best for your bike. Power Commander Installation Issues Answer Does a Power Commander make my vehicle faster? Answer Applicable to PC III USB The message "Power Commander not found" comes up on my interface. Power Commander 3 Maps Suzuki Buy Options Select MAKE, MODEL, YEAR from bike selector above Powersports Products Powercommander Powercommander V Powercommander V Pti Powercommander E-Tec Powercommander III USB Powercommander FC Powercommander Accessories POD-300 ESRM PCV Ignition

Chip, Feb 2, 2008 #2 SPATT In a gravel pit near you [email protected] said: ↑ We see it all the time.....Typical Dynojet fun. Dynojet Power Commander 3 Instructions will not reinstall. Answer Applicable to 03-09 CBR 600/1000, 04-09 GSXR 600/750, 07-09 GSXR1000 While in the Power Commander 3 USB software, the RPM reading does not show up when the bike is running. http://zx6r.com/zx6r/2767-power-commander-iii-problem.html Are you using the boot loader for the firmware update?

The Power Commander is a tuning tool to adjust fuel, and on some models ignition timing. How To Map Power Commander V Answer Applicable to PC III USB When I adjust by Power Commander using the faceplate buttons and then do a "get all" with the software I do not see any changes Is this it? Now click on Select, and then exit back to Gage setup.

Dynojet Power Commander 3 Instructions

No guesswork on your part. http://www.powercommander.com/powercommander/support/powercommander_faqs.aspx Answer Applicable to PC III USB The Power Commander software says "Serial: N/A" at the top right hand corner of the screen and does not show any serial numbers or "TP" Power Commander 3 Maps I tried it with the bike in neutral, switch in the "run" position, and both with the motor running and with just the ignition in the "on" position. Power Commander 3 Usb Maps If this is the case no adjustments made by the Power Commander, or any piggyback device, can help reduce this problem.

The light(s) should show up in the last place they were left, by default the center two lights. check my blog Once you have selected that option a window will appear that has a black rectangular button at the bottom that reads "Reset Power Commander". Answer Applicable to PC III USB The Power Commander 3 USB does not power up anymore after loading the firmware for my ignition module. Those areas do not allow devices that change the fuel curve in certain areas on pollution controlled vehicles legally driven on the street. Power Commander 3 9v Adapter

Power Commander Installation Issues Answer Do I need to disconnect my o2 sensors? KILLZONE47 16,313 views 1:43 Dynojet Kawasaki Z750 2007 Power Commander III Akrapovic remap - Duration: 3:04. If they thought you "had" to they wouldnt list all the maps that they do If you need technical assistance or have any product related questions give us a call at: http://exactcomputerrepair.com/power-commander/power-commander-error-sending-map.html Answer Jumping TPS A common problem we have seen on bikes is jumping TPS.

Metric and other: 1. Software Issues and Features Answer PCIII USB firmware update failure If the Power Commander III USB will not complete a firmware update using the control center software, check the following. Anyone have any tips or advice?Click to expand... 07 Streetglide PCIII USB Arlen Ness Big Sucker Black Thundercone slipons I know this is an old blog but I recently had a

luckily i hadnt started tearing the connectors apart to jerry rig it yet.

Onboard notes storage - The PCIII USB stores the notes from the map in the onboard memory. attempting to load a Harley map to a Suzuki). Make sure that the latest Power Commander USB software (Version 1.1.3) is installed. like a big boy ...

Short term solution 3: Customer to turn off UAC on their Windows account ( need to have Admin Rights). Some users may find that having a professional tuner setup everything as needed (including the AutoTune feature) is necessary. Last edited by CBR954a; 07-25-2010 at 07:05 PM. have a peek at these guys The injector connectors have been installed into the secondary injectors (on top of the air box), rather than the primary injectors (underneath the tank).

These models have a rubber boot that needs to be transferred from the bike's OEM connector to ours.