Home > Power Commander > Power Commander Error Sending Map

Power Commander Error Sending Map

Contents

In order to use this option, the Power Commander V has to be connected to the engine temp sensor, and temp input has to be enabled on the PCV. We use data about you for a number of purposes explained in the links below. The Power Commander V software offers the option of getting or sending a table, vs. Please, help. check over here

And by just looking at the instructions it makes me wanna puke. Where did you get the map file from? We recommend starting the bike once you turn the key on. Don't even want to think about how many shortcuts have led to how much extra work and dollars spent .

How To Map Power Commander V

Close all Power Commander Applications on your computer. 2. If they are plugged in down by the shock, the unit will not work. and how can i be sure it is done?Click to expand... The stock connector on this model does not have pins in every single space and therefore Harley-Davidson put little rubber plugs in their place to seal up the open spaces.

Answer Applicable to 03-09 CBR600/1000 There are a few connectors on these bikes which are the exact same as the TPS connector. The dual-channel AutoTune kit tunes more accurately (cylinder advanced), but is more expensive. The Power Commander software should now display the correct speed. Tuning Issues Answer Predeveloped maps The predeveloped maps on Dynojets’ website were created on a Dynamometer at our facility in Las Vegas Nevada.

Applying ample pressure is sometimes required. I'll probably end up emailing their tech support and getting a canned answer that says something like "don't do it, get it dynoed" etc. 2002 VTX 1800C, lowered stock rear shocks, Human Verification In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in http://www.vtxoa.com/forums/6-vtx-1800-tech-board/233310-power-commander-map-version-issue.html?action=thread Put the bike in first gear, and let the rear wheel spin while the bike idles.

Nijusho51 is offline Quote post #9 of 13 Old 01-19-2008, 11:43 AM Thread Starter dominick79 Squid Join Date: Jun 2007 Location: Osijek Posts: 25 I Ride: Kawasaki ZX6R Software Issues and Features Answer Can I use two maps and AutoTune at the same time? I connected and disconnected the cable several times and pushed it in quite firmly and the result was the same. The Gray wire from the Power Commander should be connected to the variable volt wire.

Power Commander 3 Usb Maps

Good luck Yeah, it took a good push until it clicked in. The Power Commander V has a utility to accept speed input, and then the unit will be able to calculate what gear you are currently in, based on that speed input. How To Map Power Commander V Small cuts may be difficult to see. Power Commander Software Each .zip file contains the same map in 2 file formats - the older .map format is from the original PC3's which had a serial port, the newer .djm format is

My lifestyle determines my deathstyle dominick79 is offline Quote post #8 of 13 Old 01-19-2008, 11:37 AM Nijusho51 Track Star Join Date: Jan 2007 Location: Gods Country Posts: http://exactcomputerrepair.com/power-commander/power-commander-error-42.html Something's got to work.Thanks for the input.Chief Logged UK Dave Elite CVO Member Offline Posts: 770 Born to be wild - well, for a few days at least Re: Error Retrieving If the fuel pump does not come on, the bike will not start. There are some older maps that do not have any values in the AFR table; you will have to fill those in yourself. Dynojet Power Commander 3 Instructions

Make sure that the unit is staying powered up (green light will be lit on the face of the unit) and the your cable is connected. You should be prompted to choose Position 1 or 2. Register Forgot Password Register Home Forum Active Topics FAQ Gallery Chat Insurance Motorcycle Escrow Go to Page... this content First you have to enable the option in the Power Commander software.

Once the vehicle is at the target speed, just press the Calibrate button. i work with computers and can tell you i've seen some really wacko shit happen with Windows and USB...Especially if it's Vista. To answer some of the other questions about the maps being zipped on my site, what I've done is zipped all the maps using a program called WinZip.

If you have an aftermarket air cleaner, select a map with an aftermarket air cleaner.

However if all that happened right in a row, I think you have another problem. 07 R6, MJS Header, GYTR slip on, smog block offs, K&N, flashed ECU, PCV, AutoTune, -1/+2. Darkside!!! If the bike is moving with the clutch out, the Power Commander will now know what gear the bike is in. The motor should stall.

Reply Tweet LinkBack Thread Tools Display Modes post #1 of 8 (permalink) Old 03-15-2008, 05:00 PM Thread Starter baggedb22 I eat my R6 Join Date: Feb 2008 Posts: 215 If you are looking at one table, and select Get or Send Table, you are only doing that one table. You are free to change these values to meet your needs or desires. http://exactcomputerrepair.com/power-commander/power-commander-usb-error-sending-file.html Release buttons.

Any ideas before i go and hunt down a spare lead incase thats the reason? If the answer to number 3 is yes, can someone post a pic of the plug and wires so i can make one up? PCVSetup5*.exe is the install for the Power Commander V. Because it's not connected to a +ve feed anywhere, only earth and the injectors, which aren't powered up if the engine isn't running.

Does the bike run the same as it did with no Power Commander? Answer Applicable to 209-411 Bike may or may not start, idles rough, and the TPS does not set correctly. For example a value of 83 would give about one second of fuel at 5000 rpm, and two seconds of fuel at 2500 rpm. I get the error message "Error Sending Power Commander Map: 0x0014 - Device Data Not Acknowledged" I pressed the lead in as hard as i could.

Product / Company Media Privacy Policy Product Warranty Follow Us Sign Up for our Newsletter! Register Now In order to be able to post messages on the Honda Motorcycles - FireBlades.org forums, you must first register. Off to Isle of Man in three days so need it sorted lol Still can't upload any pics, looking at the back of the connector (wire input side) and the connector If they are connected to holes 4 and 5, set the option to switch input 2.

A map for a Power Commander IIIUSB can be imported to the PCV. This will often give an increase in overall horsepower. If Auto-tune is enabled, you could instead use the switch to toggle the Auto-tune feature on/off “on the fly.” Software Issues and Features Answer Reset a PCIIIUSB To reset the Power Some users may find that having a professional tuner setup everything as needed (including the AutoTune feature) is necessary.

Yükleniyor... When window with CD contents opens - Right click on Setup.exe and select Run as Administrator. Undying Love Forever A.J. run the program try to install map.