Home > Power Commander > Power Commander Error Codes

Power Commander Error Codes

Contents

If you are looking at one table, and select Get or Send Table, you are only doing that one table. and different ports. Where do I get these? This button moves up & down, and left & right. check over here

everything looks fine until you run the bike for a long distance ... Idk what the hell I'm doing !?! a. Do you then really have 4 maps or do you do your performance and Eco mode in S?

Power Commander 3 Maps

Yükleniyor... Gallery Album Gallery Picture Gallery iTrader Advanced Search Forum Message Boards M109R Shop Talk Device error: 39 (Power Commander III USB) If this is your first visit, be sure to check Are they open today?

First with an ohm meter, disconnect the QS, and connect the ohm meter to each wire from the QS. After the unit is reset the error should go away. Reply Tweet LinkBack Thread Tools Display Modes post #1 of 7 (permalink) Old 07-03-2009, 10:58 PM Thread Starter Chizzled Provisional Novice Join Date: Dec 2008 Location: Las Vegas, Power Commander 3 Software To start viewing messages, select the forum that you want to visit from the selection below.

The ground wires for the Power Commander must be placed exactly per the instructions for the unit. Power Commander 3 Usb Make sure that you are using a version of Windows newer than 98 SE. 2. This is found under Power Commander Tools, Configure. That was my problem.

When this happens, the injectors get power, and the Power Commander also gets power and lights up. What Does A Power Commander Do For A Motorcycle Dynojet makes about 500 different Power Commanders; they are pretty much unique to a certain year/model vehicle. Hope this helps. With a Dynojet Power Vision you can do just that.For more information check out:www.FlashYourHarley.com Kategori Otomobiller ve Araçlar Lisans Standart YouTube Lisansı Daha fazla göster Daha az göster Bu video için

Power Commander 3 Usb

Did your pvc come with the o2 senor plugs(optimizer)? http://www.hdforums.com/forum/sportster-models/1104776-power-commander-v-check-engine-light-and-error-codes.html Dynojet has sold both types, open or closed. Power Commander 3 Maps Aaron Chizzled is offline Quote Quick Reply Remove Advertisements Sponsored Links Suzuki GSX-R Motorcycle Forums Gixxer.com Advertisement post #2 of 7 (permalink) Old 07-03-2009, 11:29 PM rraiderr !##NULL##! Power Commander 3 Instructions Non-members please click here to register.

Since there are no lights on the PC III, I agree, it's likely one of those crimp connections, or, the unit is defective. http://exactcomputerrepair.com/power-commander/power-commander-3-usb-troubleshooting.html That light comes on when the unit gets power. If custom LED tail lights are being used, they may give off interference up the line that causes the Power Commander to loose its 12 volt reference for power and shut Software Issues and Features Answer Loading a map The map in a Power Commander controls how the vehicle runs. Power Commander 3 Installation

The gains to be made with dual channel over single channel are dependent on the bike model. The Gray wire from the Power Commander should be connected to the variable volt wire. Verify that the latest version of the PCIII USB Control Center Software is installed on your computer and can communicate with the power commander 1. http://exactcomputerrepair.com/power-commander/power-commander-v-error-codes.html California.

they price matched fuel moto sale price of 299, and i had $15 credit from revzilla with free shipping. Power Commander Tech Support the rear Blue_eyes Hero Member Posts: 1089 Blue_eyes Re: The BIG Dynojet PowerCommander V and AutoTune Q&A topic « Reply #259 on: March 16, 2012, 03:52:35 am » Quote from: spasm From the main menu, go to LCD Config, Touch Panel, Start.

It's only a short ride to his shop.

No, the Power Commander is a fully sealed unit. Thanks. Then test again with a zero map. Power Commander V Tuning Tips Which I don't have. 2001 honda CR 250X 2005 suzuki gsx 1300r - sold 2000 triumph sprint rs 955i- sold 2003 yamaha YFZ-R1 -presently Reply With Quote 03-15-2011,06:31 AM #9 ped

VB search Search Home Forums Forums Community New Member Introductions General Motorcycle Discussions Off Topic Talk R1-Forum VIP lounge R1-Forum Bike of the Month Local Meets & Events Squadrons Deals Gap attempting to load a Harley map to a Suzuki). There are two versions of firmware available on the website, LCD-100 and LCD-200. have a peek at these guys It seems I am doing everything right.

Software Issues and Features Answer How do I calibrate speed input on a PCV? AutoTune Switch, if turned on, switch is in the correct position. This firmware can be updated in the field by running a firmware update. The Power Commander V only needs the USB cable to do this.