Home > Power Commander > Power Commander 3 Usb Troubleshooting

Power Commander 3 Usb Troubleshooting

Contents

i have done that ... Software Issues and Features Answer How do I lock a map on a PCIIIUSB? I took the PC off my bike and have it on my desk with a 9v battery that I can plug into it. In most cases the Power Commander can be reset and the error will go away, but if that is not the case, than the unit may need to be sent in check over here

Close the Accelerator Pump Utility that is open on your desktop.5. Especially lower and mid rpm range. An ignition timing map that works well for one customer, may not work for another customer, in another area, with different quality fuel. so ive had my bike for a long time and noticed my power commander was disconnected from the time of purchase from the dealer...

Power Commander 3 Maps

When window with CD contents opens navigate to the FS Command folder and search for PC3Setup.exe. It does not indicate that the Rev Extend feature is turned on in your Power Commander. This area is grayed out in the fuel map.

Make sure that the latest Power Commander USB software (Version 1.1.3) is installed. Sometimes the sensor can pick up metal particles from the crankcase, removing the sensor and cleaning it off may correct the problem. Would, Graves full exhaust system Graves stacks Stock or aftermarket air filter probably work for me? Power Commander Tech Support I don't know what to do now but don't really have the money for a new Powercommander.

Register Now In order to be able to post messages on the Yamaha R1 Forum: YZF-R1 Forums forums, you must first register. Power Commander 3 Instructions If you update your Ignition module, you may also need to update your Power Commander. Check the current version of firmware, it needs to be 1.0.0.20 or newer to update using the control center software.

I bought the bike secondhand with a Powercommander already fitted so I don't have anything other than the Powercommander itself.

When this happens, the injectors get power, and the Power Commander also gets power and lights up. What Does A Power Commander Do For A Motorcycle Next, run the update firmware from within the Power Commander desktop software. I can always use more go fast parts for my bike.. __________________ 2001 929, 954 ITB's w/injectors and stacks, r6 throttle, PC3 USB w/quickshift, wideband commander w/LCD, custom shorty exhaust, stretched, rees8448 2,955 views 1:50 Power commander 3 died during fireware update.

Power Commander 3 Instructions

I was sort of surprised at the symptoms the bike displayed thinking that the PCIII would either 'work or not work' as they say. his comment is here Uncheck the box next to Diagnostic Port Enabled. Power Commander 3 Maps Loading... Power Commander 3 Installation The correct map should make the engine run well; the wrong map may cause the engine to run poorly.

Does the bike run the same as it did with no Power Commander? check my blog If yes, then load a zero map from us to the Power Commander. Applying ample pressure is sometimes required. You can read about them here.X LinkBack LinkBack URL About LinkBacks Remember Me? Power Commander 3 Software

Once clicked Windows will ask you to block or allow select allow. Darksider #52FJRForum: No fun allowed here!FJR#1 - The 'Dirty Ol Whore' - 2004 non-abs - RIP @ 226,400 - Gone, but not forgotten.FJR#2 - The 'Hula Girl' - 2004 ABS - At this point holding that button down will move the lights down (leaning out the mixture).Pushing the button repeatedly will move the light up (richening the mixture). this content You don't have to rev the bike out, the throttle just needs to go all the way to wide open and then back to idle.

If you are looking at one table, and select Get or Send Table, you are only doing that one table. Power Commander V Tuning Tips Join Date: Apr 2011 Location: Utah Posts: 26 Why are there so many different maps for each kind of slip-on? Power Commander Accessory Issues Answer Can I have AutoTune start working after a certain engine temperature?

The best way to confirm your sensor type is with an Ohmmeter.

If the version number is 4.10.2222, it is the “SE” version. If they are connected to holes 4 and 5, set the option to switch input 2. There are two identical sets of connectors on this bike. Power Commander 3 Usb Maps If yours is not reading “zero” at idle with the motor at normal temperature, then use the following procedure to correct it.

All of the software, map files, etc., can be found on the web site at Power Commander Select your bike model. Once you have sent two maps to the Power Commander, every time you Send or Get Map, it will perform that function on the map that is selected. Make sure that the rubber boot, if it was installed, does not have any holes and is securely placed to keep water out as much as possible. http://exactcomputerrepair.com/power-commander/power-commander-error-39.html Today 05:57 PM by RideRed31B 19 30 Attachment(s) Help Please!?2004 1000RR...

The Power Commander software does not show an ignition table, either. how do I fix it? Answer Applicable to PC III USB When I adjust by Power Commander using the faceplate buttons and then do a "get all" with the software I do not see any changes Now sitting still with the bike running in neutral, pull in the clutch and move the shifter into second with your foot.

Your cache administrator is webmaster. So they probably charge a ton. Answer All Models My engine makes a popping noise on deceleration, how to I get rid of this? Next select Edit next to Channel.