Home > Power Commander > Power Commander 3 Troubleshooting

Power Commander 3 Troubleshooting

Contents

The motor is running at an RPM and Throttle position that has a valid number in the target AFR table. TOO MANY THINGS ALL AT ONCE. Dennis grrwrr 1,382 views 4:53 How to fit a Power Commander III to GSXR 750 K7 - Duration: 5:03. Thread Tools Show Printable Version Subscribe to this Thread… 07-08-2011,08:04 PM #1 hammat1me Newbie My Bike(s) a pink scooter Posts 18 Power Commander 5 troubleshooting Hi all, I have been looking http://exactcomputerrepair.com/power-commander/power-commander-3-usb-troubleshooting.html

The Second test is the static configuration test. Software Issues and Features Answer How do I calibrate speed input on a PCV? Password: Confirm Password: Email Address Please enter a valid email address for yourself. Metric and other: 1. Check This Out

Power Commander 3 Maps

There should be three factory wires going to the TPS sensor; ground, constant 5 volts, and variable volts. Answer Applicable to 03-09 CBR600/1000 There are a few connectors on these bikes which are the exact same as the TPS connector. They will then be required to re-Start their computer. Adjusting the ignition table could also help in deceleration popping.

Starting Line Products, primarily Polaris, 208-529-0244 Dynotech Research, primarily Ski-Doo, 585-993-2777 Ulmer Racing, primarily Yamaha, 605-387-2833 Speedwerx, primarily Arctic Cat, 651-982-6020 Tuning Issues Answer Harley crank error or no start If Contact Us Advertise Motorcycle Forum Archive Privacy Statement Top All times are GMT -5. Highlight the zero percent column and instead of using negative numbers, try adding fuel to the map. Power Commander 3 Software The ground wires for the Power Commander must be placed exactly per the instructions for the unit.

Adjusting the ignition table could also help in deceleration popping. Power Commander 3 Usb Back to top #6 gixxerjasen gixxerjasen FJR Commander Members++ 3,037 posts Gender:Male Location:DFW 2007 ABS AE (Gen II) N. The drivers required are found on the install disk for Windows 98SE. If you are using a Power Commander then while communicating to the software press one, and the highlighted area will represent that button.

Human Verification In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in What Does A Power Commander Do For A Motorcycle Dynojet is very conservative in giving out maps to customers everywhere in the world. The fix is very easy. Now press the three keys Ctrl – Alt – M at the same time.

Power Commander 3 Usb

Answer Applicable to PC III USB The firmware program does not appear to work and I get an error code that has a "0x005, 0x008, 8001" or something similar.

Reply With Quote 07-10-2011,07:14 PM #8 Easy Rider Super Moderator My Bike(s) '10 Kaw Vulcan 900 Custom Location Ocala, FL Posts 10,677 Originally Posted by hammat1me I wonder if maybe we Power Commander 3 Maps Sign in 2 0 Don't like this video? Power Commander 3 Instructions If no, the Power Commander is not working correctly, try a firmware update.

What does the “SE” mean? check my blog Autotune Answer HD Cruise control, 6th gear light If you experience any problems with cruise control, or 6th gear indicator light on a newer Harley Davidson Touring bike with a Power Click Position 2. Power Commander Installation Issues Answer Does a Power Commander make my vehicle faster? Power Commander 3 Installation

That is usually the problem especially if you grounded it where the instructions said to (behind the coolant reservoir). Answer Applicable to PC III USB The Power Commander software says "Serial: N/A" at the top right hand corner of the screen and does not show any serial numbers or "TP" rees8448 2,955 views 1:50 Powercommander not working - Duration: 2:19. this content Member Posts: 99 Country: Re: power commander v failure « Reply #7 on: June 03, 2011, 09:00:30 am » Quote from: Cap'n Bob on June 03, 2011, 06:51:18 am Dynojet recommends

I'm sure once you get everything squared away, you'll get plenty of worry free miles out of you PC-V. Power Commander Tech Support Dynojet creates target AFR tables for most of our pre-configured maps. Just download and save the latest firmware, and then unzip the file someplace you can find quickly on your computer, like the desktop.

I had to grind some metal down and used an additional washer on mine to make sure I had a good connection.

Show more Language: English Content location: United States Restricted Mode: Off History Help Loading... Back to top #11 JamesK JamesK Got to ride Members++ 1,668 posts Gender:Male Location:Tokyo, Japan 2007 ABS (Gen II) N. Make sure that the latest Power Commander USB software (Version 1.1.3) is installed. Power Commander V Tuning Tips Close all Power Commander Applications on your computer. 2.

You don't have to rev the bike out, the throttle just needs to go all the way to wide open and then back to idle. But don't get it too big as it might cause binding at the tank/frame junction. (cost approx 15 cents) a small razor knife Wrap/insulate the area surrounding the bare spot using For this reason we recommend that you use a map that coincides with the region in that you live in. http://exactcomputerrepair.com/power-commander/power-commander-error-39.html Dynojet Research Inc 79,312 views 6:52 2003 kawasaki zx6r POLICE CHASE yorktown, cortland manor, peekskill NY - Duration: 5:46.

Please verify in the instructions. carolinaaag1 1,727 views 2:31 powercommander 3 usb test German - Duration: 4:53. This will often give an increase in overall horsepower. There is a difference.

Sign in to make your opinion count. Working... For example a value of 83 would give about one second of fuel at 5000 rpm, and two seconds of fuel at 2500 rpm. Ft.

Software Issues and Features Answer Do I need to use Get/Send Map or Table on the PCV? I had a power commander fail on my cbr1100xx and it left me stranded on the side of the highway. I bought the bike secondhand with a Powercommander already fitted so I don't have anything other than the Powercommander itself. Make sure that the ignition module is communicating with the bike by showing a green indicator light on the front of the module once the bike is started.

If the light is not on, then the placement of the wires in the white connector on the shifters harness needs to be checked. If the fuel pump does not come on, the bike will not start. The Power Commander III USB needs the 9 volt adapter to do a firmware update. Copyright, Trademark and Disclaimer Notices | © 1995 - Dynojet Research, Inc.

What should I check? This allows the settings to be saved to memory. Worth, TX, IBA #288FJR-Tips.org Back to top #3 Hornet Pilot Hornet Pilot Viper Pilot Members++ 192 posts Gender:Male Location:Pewaukee, WI 2005 (Gen I) N. Watch QueueQueueWatch QueueQueue Remove allDisconnect The next video is startingstop Loading...