Home > Post Error > Post Error Code Of 161

Post Error Code Of 161

Contents

Its a POST code, Power On Self Test error code. As a computer technician, I rely on documentation to guide me through these types of messages. Use the Configuration/Setup Utility program (Advanced Setup → PCI Bus Control → PCI ROM Control) to disable each optional device one at a time, restarting the blade server each time, until Whenever I power on the Thread Tools Search this Thread 01-20-2006, 05:34 AM #1 chessypoofs Registered Member Join Date: Apr 2005 Location: Oahu, Hawaii Posts: 86 OS: xp http://exactcomputerrepair.com/post-error/post-error-code-161.html

Reseat each I/O expansion card, restarting the blade server each time. Replace the following components one at a time, in the order shown, restarting the blade server each time: Failed I/O expansion card - See Removing an I/O expansion card andInstalling an See Using the Configuration/Setup Utility program. Hot-swap storage drive - See Removing a hot-swap storage drive and Installing a hot-swap storage drive. http://ps-2.kev009.com/eprmhtml/eprmx/h12290.htm

Post Error Codes List

Run the Configuration/Setup Utility program and make sure that the PXE settings are correct. Replace the following components one at a time, in the order shown, restarting the blade server each time: (Trained service technician only) Microprocessor - See Removing a microprocessor and heat sink Replace the following components one at a time, in the order shown, restarting the blade server each time: (Trained service technician only) Microprocessor - See Removing a microprocessor and heat sink Remove each I/O expansion card one at a time, restarting the blade server each time, until the problem is isolated.

thinkpad 600e 161 and 163 error This is a discussion on thinkpad 600e 161 and 163 error within the Laptop Support forums, part of the Tech Support Forum category. Replace the following components, one at a time, in the order shown, restarting the blade server each time: I/O expansion card in slot xx - Optional expansion unit (if one is Replace the following components, one at a time, in the order shown, restarting the blade server each time: (Trained service technician only) Microprocessor - See Removing a microprocessor and heat sink I note that with only the native 32Mb installed the memory tests "OK".

Replace the following components one at a time, in the order shown, restarting the blade server each time: Battery - See Removing the battery and Installing the battery. (Trained service technician What Dos Command Do You Use To Erase A Hard Drive And Make It Bootable? If an optional expansion unit is installed, reseat it - See Removing an optional expansion unit and Installing an optional expansion unit. And, yes, people still use them and some refuse to give them up. http://www.bioscentral.com/misc/ibmdiag.htm See Using the Configuration/Setup Utility program.

Optional devices that cause the 1801 error code are the I/O expansion cards and optional expansion unit. See Solving shared BladeCenter resource problems. (Trained service technician only) Replace the system-board assembly - See Removing the system-board assembly and Installing the system-board assembly. 604 Diskette drive failure. If you have installed a USB keyboard, run the Configuration/Setup Utility program (Using the Configuration/Setup Utility program), and enable the keyboardless operation to prevent the POST error message 301 from being Presumably something wrong.

What Dos Command Do You Use To Erase A Hard Drive And Make It Bootable?

I'm not sure of what the password is... Optional expansion unit - See Removing an optional expansion unit and Installing an optional expansion unit. (Trained service technician only) If the problem remains after all optional devices have been removed, Post Error Codes List Replace a DIMM - See Removing a memory module and Installing a memory module. Which Of The Following Might Conflict With A Network Adapter On Irq3? Replace the following components, one at a time, in the order shown, restarting the blade server each time: (Trained service technician only) Microprocessor - See Removing a microprocessor and heat sink

If an optional expansion unit is installed, reseat it - See Removing an optional expansion unit and Installing an optional expansion unit. check my blog Replace the following components, one at a time, in the order shown, restarting the blade server each time: I/O expansion card in slot xx - Optional expansion unit (if one is The method for reading these codes is pretty straight forward. But if I have to replace the backup battery, what does "reset the CMOS values" mean? Ibm

Run the Configuration/Setup Utility program, make sure that the hard disk drive configuration is correct, and save the settings. A fault code of 00 indicates that no problem was found. Optional expansion unit (if one is installed) - See Removing an optional expansion unit and Installing an optional expansion unit. this content Run the Configuration/Setup Utility program and make sure that interrupt resource settings are correct.

Optional expansion unit (if one is installed) - See Removing an optional expansion unit and Installing an optional expansion unit. (Trained service technician only) System-board assembly - See Removing the system-board All rights reserved. I have a 1998 Thinkpad 385XD Win 98 FE, ca 3GB HD.

Replace the following components one at a time, in the order shown, restarting the blade server each time: Failed I/O expansion card - See Removing an I/O expansion card and Installing

Optional expansion unit (if one is installed) - See Removing an optional expansion unit and Installing an optional expansion unit. (Trained service technician only) System-board assembly - See Removing the system-board See Solving shared BladeCenter resource problems. (Trained service technician only) Replace the system-board assembly - See Removing the system-board assembly and Installing the system-board assembly. 1200 Processor machine check. (Trained service System Board Errors: Code Description 101 System board interrupt failure (unexpected interrupt) 102 BIOS ROM checksum error (PC, XT); timer error (AT, MCA) 103 BASIC ROM checksum error (PC, XT); timer By continuing to browse our site you agree to our use of data and cookies.Tell me more | Cookie Preferences Partially Powered By Products Found At Lampwrights.com POST error

Update the blade server firmware. Replace the following components one at a time, in the order shown, restarting the blade server each time. I9990303 No Boot devices found Install the operating system on the storage drive - See Installing the operating system. http://exactcomputerrepair.com/post-error/post-error-code-25h.html Reseat the I/O expansion card in slot xx; then, restart the blade server.

Wanting to be able to use a wireless PC card, I installed a 20 GB HD and Win ME. Optional expansion unit (if one is installed) - See Removing an optional expansion unit and Installing an optional expansion unit. (Trained service technician only) System-board assembly - See Removing the system-board Reseat the I/O expansion card in slot xx; then, restart the blade server. After resetting date and time all is well.

Replace the following components, one at a time, in the order shown, restarting the blade server each time: (Trained service technician only) Microprocessor - See Removing a microprocessor and heat sink Open the plate on the bottom to access the battery (CR2027 I think) and replace it with a new one. Thanks 06-20-2006, 08:14 AM #9 laboye TSF Team, Emeritus Join Date: Apr 2006 Location: Hollywood, FL Posts: 1,246 OS: Windows xp Pro/Vista Beta 2/Ubuntu 6.06 LTS My System Restart the blade server, run the Configuration/Setup Utility program (Using the Configuration/Setup Utility program), and change the power-on password (Using passwords). 289 Memory error Run the Configuration/Setup Utility program (Using the

Parent topic: POST Notices | Terms of use | Privacy | Support | Feedback 简体中文 正體中文 (繁體) Česky Danish Deutsch English Español (Castellano) Eesti keel Français Hrvatski Magyar Italiano 日本語 Cyc. Reseat the I/O expansion card in slot xx; then, restart the blade server. The error codes you see are actually pointers in what spost are bad in the memory.